AMX DXLink Multi-Format SMF-D Manuel d'instructions Page 97
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix B – Telnet (Terminal) Commands
97
Instruction Manual – DXLink™ Fiber Transmitters and Receivers, Duplex
Telnet Commands (continued)
DEVICE STATUS Displays device status of a specified device, port, system (<D:P:S>).
Note: Devices other than the DXLink Fiber device itself will be ignored.
Example:
>device status 32002:1:0
Device Status
-------------
Device 32002 AMX LLC, DXLF-MFTX, 0.0.105.0 contains 8 Ports
Port 1 - Channels:255 Levels:8
MaxStringLen=64 Types=8 bit MaxCommandLen=64 Types=8 bit
The following input channels are on:None
The following output channels are on:None
Level 1=0 Supported data types=UByte,UInt
Level 2=0 Supported data types=UByte,UInt
Level 3=0 Supported data types=UByte,UInt
Level 4=0 Supported data types=UByte,UInt
Level 5=0 Supported data types=UByte,UInt
Level 6=0 Supported data types=UByte,UInt
Level 7=0 Supported data types=UByte,UInt
Level 8=0 Supported data types=UByte,UInt
DIPSWITCH Displays the current value for each of the DIP switch’s four toggles.
Example:
>dipswitch
Board Switch Settings:
ON : ICS LAN Enabled
OFF : Reserved
ON : Network Enabled
OFF : Reserved
DNS LIST Displays list of DNS settings.
Example:
>dns list
DNS List
-------------
Domain suffix: amx.internal
The following DNS IPs are configured
Entry 1: 192.168.40.7
Entry 2: 192.168.40.8
ECHO Note: This command applies only to the Transmitter.
Toggles echo of local characters on and off. Enter “echo on” or “echo off” or simply re-enter
“echo” to toggle between on and off.
encoder
Note: This command
must be entered in lower
case only.
Note: This command applies only to the Receiver.
Shows video encoder status.
Example:
>encoder
--------------------------------
Video Encoder (ADV7511)
TMDS On
Mute Unmuted
HDCP Screen No
EXIT Closes the current Telnet session.
FACTORY APP Note: This command only applied to the Transmitter.
Resets the application to the factory image.
Note: This command does not reset the factory parameters.
FACTORYFWIMAGE Resets unit to factory firmware image and parameters and reboots the DXLink Fiber unit.
Note: When a Transmitter is connected to a DXLink Fiber Input Board, the input board will
override the “ALL RESOLUTIONS” EDID and load the last stored EDID.
FWIMAGES Displays firmware version information.
- Instruction Manual 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Apache License, Version 2.0 10
- Warnings and Cautions 11
- Applicability Notice 12
- Product Notes 13
- Product Compatibility 15
- Common Applications 17
- Power Jack 18
- Video In Connector 18
- Overview DXLink Fiber, Duplex 19
- Fiber Optic Transceiver 20
- Common Features/Functionality 23
- DXLink Fiber Receiver, Duplex 24
- HID Devices and Windows 8 24
- 4. Click OK 25
- DXLink Fiber Specifications 28
- qualified): 1 per unit 29
- HDMI Specifications 30
- Analog Video Specifications 32
- Local Audio Specifications 33
- Installation and Setup 34
- Setup Information 35
- Example 36
- Endpoint/ 36
- Bidirectional 36
- Example B 37
- Example C 37
- Example A 37
- DIP Switch Location 38
- Setting DIP Switch #2 39
- Setting DIP Switch #4 39
- V Style mounting hardware 40
- Audio Type Precedence 42
- ICS LAN 10/100 LEDs 42
- ID Pushbutton Functions 49
- To set the Scaling Mode: 50
- Bypass Mode 50
- Auto Mode 50
- Manual Mode 50
- Persistence of Scaling Mode 51
- Network Configuration 54
- TCP/IP Address Configuration 55
- Factory Default Parameters 56
- Device IDs 57
- Using the ID Pushbutton 57
- Factory Parameters* 59
- IRL File Transfers 61
- Transferring IRL Files 63
- Additional Documentation 65
- Additional IRL Information 65
- Device Numbering and Ports 66
- VIDOUT_SCALE 68
- Scaling Modes 68
- VIDOUT_RES_REF 68
- SEND_COMMAND 68
- VI<input>O 71
- <output> 71
- VIDIN_EDID 73
- IR CHANNELs 76
- IR SEND_COMMANDs 76
- AUDIN_FOR 76
- CH SEND_COMMAND 77
- XCH SEND_COMMAND 78
- USB SEND-COMMANDs (Receiver) 82
- PERSISTAV 84
- SEND_STRING Escape Sequences 85
- Troubleshooting 86
- Network Setup Issues 87
- DXLink Fiber Troubleshooting 87
- Technical Support 88
- Important Upgrade Information 90
- Transferring KIT Files 91
- Firmware Versions 92
- Example: 93
- Telnet Username and Password 94
- Telnet Commands (continued) 100
- Guidelines 108
- TCP vs. UDP 108
- URL vs. NDP vs. Auto 109
- Windows Client Programs 109
- Linux Telnet Client 109
- Creating a Virtual Master 112
- CONNECTION and press Enter 115
- Overview 116
- HDMI Connector Cable Pinout 116
- HD-15 Connector Cable Pinout 117
- DVI Cable Connector Pinout 118
- CEA (RGB Color Space): 123
- CVR (RGB Color Space): 124
- CVT (RGB Color Space): 125
- DMR (RGB Color Space): 126
- DMT (RGB Color Space): 126
- DXLink Fiber and EDID 130
- USER EDID 1 131
- USER_EDID_MODIFIED 131
- MIRROR OUT 1 131
- MIRROR_OUT_LOCAL 131
- AMX EDID Library 131
- Software Installation on PC 132
- DXLink Fiber Connection to PC 133
- EDID Programmer tab 133
- EDID Programmer View 134
- Read Error Message 136
- 02/28/14 137
Produits connexes et manuels pour Équipement musical supplémentaire AMX DXLink Multi-Format SMF-D
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.820 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels