AMX DXLink Multi-Format SMF-D Manuel d'instructions Page 93
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix B – Telnet (Terminal) Commands
93
Instruction Manual – DXLink™ Fiber Transmitters and Receivers, Duplex
Appendix B – Telnet (Terminal) Commands
Establishing a Terminal Connection Via Telnet
Telnet terminal communication is accessed remotely via TCP/IP. The DXLink Fiber Transmitter or Receiver must have
its own TCP/IP address for a Telnet connection. The connection can be started from the Windows taskbar (see below) or
in NetLinx Studio (see the following page).
By default, a username and password are not applied to the Telnet port (Port 23). Therefore, the port does not require
login credentials. If you require a username and password for security purposes, directions for setting them are on
page 95.
Welcome Banner with and without security enabled (Receiver shown):
Without Telnet security enabled, a session will begin with a welcome banner similar to the following:
Welcome to DXLF-HDMIRX v0.9.12 Copyright AMX LLC 2014
>
If Telnet security is enabled, user credentials are required:
Enter username: admin
Enter protected password: ****
Welcome to DXLF-HDMIRX v0.9.12 Copyright AMX LLC 2014
>
Note: When security is enabled, a user can retry logging in three times before being disconnected (for
information on setting a username and password, see page 95).
To establish a terminal connection via Telnet at the CMD prompt:
1.
From your Windows Taskbar (at far left), select Start > Run to open the Run dialog box.
2. Type cmd in the Open field.
3. Click OK to open an instance of the Windows command interpreter (cmd.exe).
4. At the prompt (>), type telnet followed by a space and the Transmitter or Receiver’s IP address. Press Enter.
Example:
>telnet XXX.XXX.XXX.XXX
A Telnet session opens for the Transmitter or Receiver and the Welcome Banner appears.*
5. At the prompt, type the Telnet command (see the table starting on page 95) and press Enter.
* If you are using Windows 7 and receive an error message, you may need to enable Telnet by completing the following:
(1) Go to Start / Control Panel / Programs and Features. (2) On the left, select “Turn Windows features on or off.”
(3) Select the check-boxes Telnet Client and Telnet Server. (4) Click OK.
- Instruction Manual 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Apache License, Version 2.0 10
- Warnings and Cautions 11
- Applicability Notice 12
- Product Notes 13
- Product Compatibility 15
- Common Applications 17
- Power Jack 18
- Video In Connector 18
- Overview DXLink Fiber, Duplex 19
- Fiber Optic Transceiver 20
- Common Features/Functionality 23
- DXLink Fiber Receiver, Duplex 24
- HID Devices and Windows 8 24
- 4. Click OK 25
- DXLink Fiber Specifications 28
- qualified): 1 per unit 29
- HDMI Specifications 30
- Analog Video Specifications 32
- Local Audio Specifications 33
- Installation and Setup 34
- Setup Information 35
- Example 36
- Endpoint/ 36
- Bidirectional 36
- Example B 37
- Example C 37
- Example A 37
- DIP Switch Location 38
- Setting DIP Switch #2 39
- Setting DIP Switch #4 39
- V Style mounting hardware 40
- Audio Type Precedence 42
- ICS LAN 10/100 LEDs 42
- ID Pushbutton Functions 49
- To set the Scaling Mode: 50
- Bypass Mode 50
- Auto Mode 50
- Manual Mode 50
- Persistence of Scaling Mode 51
- Network Configuration 54
- TCP/IP Address Configuration 55
- Factory Default Parameters 56
- Device IDs 57
- Using the ID Pushbutton 57
- Factory Parameters* 59
- IRL File Transfers 61
- Transferring IRL Files 63
- Additional Documentation 65
- Additional IRL Information 65
- Device Numbering and Ports 66
- VIDOUT_SCALE 68
- Scaling Modes 68
- VIDOUT_RES_REF 68
- SEND_COMMAND 68
- VI<input>O 71
- <output> 71
- VIDIN_EDID 73
- IR CHANNELs 76
- IR SEND_COMMANDs 76
- AUDIN_FOR 76
- CH SEND_COMMAND 77
- XCH SEND_COMMAND 78
- USB SEND-COMMANDs (Receiver) 82
- PERSISTAV 84
- SEND_STRING Escape Sequences 85
- Troubleshooting 86
- Network Setup Issues 87
- DXLink Fiber Troubleshooting 87
- Technical Support 88
- Important Upgrade Information 90
- Transferring KIT Files 91
- Firmware Versions 92
- Example: 93
- Telnet Username and Password 94
- Telnet Commands (continued) 100
- Guidelines 108
- TCP vs. UDP 108
- URL vs. NDP vs. Auto 109
- Windows Client Programs 109
- Linux Telnet Client 109
- Creating a Virtual Master 112
- CONNECTION and press Enter 115
- Overview 116
- HDMI Connector Cable Pinout 116
- HD-15 Connector Cable Pinout 117
- DVI Cable Connector Pinout 118
- CEA (RGB Color Space): 123
- CVR (RGB Color Space): 124
- CVT (RGB Color Space): 125
- DMR (RGB Color Space): 126
- DMT (RGB Color Space): 126
- DXLink Fiber and EDID 130
- USER EDID 1 131
- USER_EDID_MODIFIED 131
- MIRROR OUT 1 131
- MIRROR_OUT_LOCAL 131
- AMX EDID Library 131
- Software Installation on PC 132
- DXLink Fiber Connection to PC 133
- EDID Programmer tab 133
- EDID Programmer View 134
- Read Error Message 136
- 02/28/14 137
Produits connexes et manuels pour Équipement musical supplémentaire AMX DXLink Multi-Format SMF-D
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.697 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels