AMX DXLink Multi-Format SMF-D Manuel d'instructions télécharger pdf (Page 46)

Installation and Setup

Instruction Manual – DXLink Fiber™ Transmitters and Receivers, Duplex

6. USB port (optional) – This port is for sending keyboard / mouse commands to a PC. You can either connect this

port to a hub using a USB mini-A cable and then connect keyboard and mouse to the hub or connect directly to a

keyboard or mouse using the appropriate mini-A plug adapter cable. The port’s default is “enabled.” The USB LED

on the front monitors this port. For USB support information, see page 23. For USB SEND_COMMAND

information, see page 82.

7. Stereo Audio Out connector (optional) – Plug the audio cable (that goes to the audio destination) into the stereo

audio jack. For audio precedence information, see page 42. For information on audio SEND_COMMANDs

(including enabling the analog audio format), see page 70.

Note: When digital audio and/or analog stereo audio cables are plugged into the TX, the Audio LEDs on the

front of both units turn green to show that audio is present and is being incorporated into the HDMI line and is

also available on the DXLink Fiber RX at the Stereo Audio Out connector.

Note: The ID Pushbutton places the DXLink Fiber RX in ID Mode for setting the NetLinx ID (device only) and

provides additional functionality, such as placing the device in Static IP Mode or DHCP Mode. For information,

see page 57.

Tip: If scaling adjustments are necessary, use SEND_COMMANDs (see page 66). DGX Configuration

Software via the Enova DGX Digital Media Switcher outputs can be used for scaling.

DXLink Fiber RX – Applying Power

To apply power to the DXLink Fiber RX:

Plug the cord from the desktop power supply (provided) into the power jack on rear of the DXLink Fiber RX

(2.1 mm DC jack for 12 V local power).

2. Plug the desktop power supply into an AC external power source.

The Power LED on the front of the DXLink Fiber RX illuminates a constant green, which indicates a ready state.

Some LEDs turn a turn a constant color while some blink first. For normal LED display, see the table below.

DXLink Fiber Receivers, Duplex – Indicator LEDs

The LED indicators are listed in the table as they appear on the front of the RX from left to right.

* When the HDMI output cable is disconnected from the DXLink Fiber RX or if no EDID is found on the destination device,

the Auto LED is ON. In both cases, the DXLink Fiber RX will revert to a resolution of 1280x1024 @ 60 Hz until a different

EDID is detected.

Caution: The provided desktop power supply must be used to power the DXLink Fiber RX, and it must not

be altered in any way.

DXLink Fiber RX LEDs

Normal Display Indicates

Power Green Power is applied to the Receiver

Video Green A video signal is present through the Receiver

Audio Green An embedded audio signal is present through the Receiver

Scaling:

– Bypass

– Auto

– Manual

One LED is green.

The other two are off.

Receiver is in one of the three modes for scaling

• At power up, the Receiver defaults to Auto Mode, unless a

different Scaling Mode has been persisted*

• Press the Scaling button to turn on Bypass or Manual

IR TX Red IR TX active communication

IR RX Yellow IR RX active communication

Serial TX Red Serial TX active communication

Serial RX Yellow Serial RX active communication

NetLinx Link/Act Green Active LAN connection to an AMX Network

NetLinx Status Green LAN connection is active

CEC OFF CEC is not currently supported

USB Yellow USB port connection is established

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 136 137

Commentaires sur ces manuels

Pas de commentaire

AMX DXLink Multi-Format SMF-D Manuel d'instructions Page 46

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement musical supplémentaire AMX DXLink Multi-Format SMF-D