AMX DXLink Multi-Format SMF-D Manuel d'instructions Page 58
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Network Configuration
58
Instruction Manual – DXLink Fiber™ Transmitters and Receivers, Duplex
To toggle between DHCP and Static IP Modes:
1.
Once the TX/RX unit has booted up, press and hold the ID Pushbutton until the Control/NetLinx LEDs toggle
back and forth in unison approximately 10 times.
2. Release when the LED starts to blink faster.
When the ID Pushbutton is released, the unit toggles either from static to dynamic (DHCP) IP addressing or
vice versa and remains in that mode until the ID Pushbutton is used to set it again or a factory reset is
performed.
The DXLink Fiber unit automatically reboots to complete the process.
Assign a Device Address (ID Mode)
The ID Pushbutton can be used in conjunction with the ID (Identify) Mode feature in NetLinx Studio. A momentary
press of the ID Pushbutton assigns a device address to the Transmitter or Receiver (which must be bound to the Master).
The device must first be placed in ID Mode in NetLinx Studio or the momentary press will be ignored.
Note: The latest version of NetLinx Studio is available to download and install from www.amx.com
. Refer to
the NetLinx Studio Online Help for instructions on using the application.
To set the device address on a Transmitter or Receiver:
1.
Check to be sure #3 Toggle on the bottom of the Transmitter or Receiver is set to ON.
2. In NetLinx Studio’s OnLine Tree, select the Master to which the unit is bound.
3. From the Diagnostic menu, select Device Addressing.
The Device Addressing dialog box opens.
4. In the ID Mode section, enter the Device and System numbers that you want assigned to the device in the
appropriate text boxes.
5. Click Start Identify Mode to place the named system in ID Mode.
The button changes to “Cancel Identify Mode” (click to cancel ID Mode).
The text box below the button displays a “Waiting...Press Cancel to Quit” message.
Note: When in ID Mode, the entire system is put on hold while it waits for an event from any NetLinx device in
the named system (e.g., pressing the ID Pushbutton on the Receiver). The device that generates the first
event is the device that will be “identified.”
6. Briefly press and release the ID Pushbutton on the Transmitter or Receiver.
The unit will exhibit the following behavior:
Respond with an ID Mode address response.
Report its old address offline.
Report its new address online.
The OnLine Tree will refresh to display the new device address for the Transmitter or Receiver.
Note: NetLinx Studio (v3.3 or higher) provides the ability to auto-increment IP Addresses and Hostnames as
well as Device and System Numbers. Refer to the NetLinx Studio Online Help for details.
- Instruction Manual 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Apache License, Version 2.0 10
- Warnings and Cautions 11
- Applicability Notice 12
- Product Notes 13
- Product Compatibility 15
- Common Applications 17
- Power Jack 18
- Video In Connector 18
- Overview DXLink Fiber, Duplex 19
- Fiber Optic Transceiver 20
- Common Features/Functionality 23
- DXLink Fiber Receiver, Duplex 24
- HID Devices and Windows 8 24
- 4. Click OK 25
- DXLink Fiber Specifications 28
- qualified): 1 per unit 29
- HDMI Specifications 30
- Analog Video Specifications 32
- Local Audio Specifications 33
- Installation and Setup 34
- Setup Information 35
- Example 36
- Endpoint/ 36
- Bidirectional 36
- Example B 37
- Example C 37
- Example A 37
- DIP Switch Location 38
- Setting DIP Switch #2 39
- Setting DIP Switch #4 39
- V Style mounting hardware 40
- Audio Type Precedence 42
- ICS LAN 10/100 LEDs 42
- ID Pushbutton Functions 49
- To set the Scaling Mode: 50
- Bypass Mode 50
- Auto Mode 50
- Manual Mode 50
- Persistence of Scaling Mode 51
- Network Configuration 54
- TCP/IP Address Configuration 55
- Factory Default Parameters 56
- Device IDs 57
- Using the ID Pushbutton 57
- Factory Parameters* 59
- IRL File Transfers 61
- Transferring IRL Files 63
- Additional Documentation 65
- Additional IRL Information 65
- Device Numbering and Ports 66
- VIDOUT_SCALE 68
- Scaling Modes 68
- VIDOUT_RES_REF 68
- SEND_COMMAND 68
- VI<input>O 71
- <output> 71
- VIDIN_EDID 73
- IR CHANNELs 76
- IR SEND_COMMANDs 76
- AUDIN_FOR 76
- CH SEND_COMMAND 77
- XCH SEND_COMMAND 78
- USB SEND-COMMANDs (Receiver) 82
- PERSISTAV 84
- SEND_STRING Escape Sequences 85
- Troubleshooting 86
- Network Setup Issues 87
- DXLink Fiber Troubleshooting 87
- Technical Support 88
- Important Upgrade Information 90
- Transferring KIT Files 91
- Firmware Versions 92
- Example: 93
- Telnet Username and Password 94
- Telnet Commands (continued) 100
- Guidelines 108
- TCP vs. UDP 108
- URL vs. NDP vs. Auto 109
- Windows Client Programs 109
- Linux Telnet Client 109
- Creating a Virtual Master 112
- CONNECTION and press Enter 115
- Overview 116
- HDMI Connector Cable Pinout 116
- HD-15 Connector Cable Pinout 117
- DVI Cable Connector Pinout 118
- CEA (RGB Color Space): 123
- CVR (RGB Color Space): 124
- CVT (RGB Color Space): 125
- DMR (RGB Color Space): 126
- DMT (RGB Color Space): 126
- DXLink Fiber and EDID 130
- USER EDID 1 131
- USER_EDID_MODIFIED 131
- MIRROR OUT 1 131
- MIRROR_OUT_LOCAL 131
- AMX EDID Library 131
- Software Installation on PC 132
- DXLink Fiber Connection to PC 133
- EDID Programmer tab 133
- EDID Programmer View 134
- Read Error Message 136
- 02/28/14 137
Produits connexes et manuels pour Équipement musical supplémentaire AMX DXLink Multi-Format SMF-D
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.366 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels