AMX DXLink Multi-Format SMF-D Manuel d'instructions Page 47
- Page / 137
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Setup
47
Instruction Manual – DXLink Fiber™ Transmitters and Receivers, Duplex
DXLink Fiber Receivers, Duplex – LED Troubleshooting
If the indicator LEDs for the units do not respond with a normal display as stated in the table on the previous page:
Check all power connections.
Check the “Detailed NetLinx (Link/Act and Status) LED Behavior” section on page 52.
Try the suggestions in the “Troubleshooting” chapter (page 86).
For information on restoring the unit’s default settings on power up, see page 59.
Serial Data Transfer and IR Flow Control
The illustration in FIG. 19 shows the bidirectional serial data transfer and IR flow control when DXLink Fiber units are
used in Endpoint Mode with an Enova Digital Media Switcher. The switcher has an integrated NetLinx Central Control
Processor which provides native AMX control at each remote location fed by a DXLink Fiber Transmitter / Receiver.
Control is sent over fiber optic cable (via the fiber optic transceivers).
Wiring for Serial Data Transfer
The RS-232 (serial) ports are the 3-position screw terminal blocks on the rear of the units to the right of the
ICS LAN 10/100 connector. The RS-232 ports can be bound and controlled via the integrated NetLinx Central
Controller in the Enova DGX or via another network connected NetLinx Central Controller. For an illustration of serial
data transfer, see FIG. 19.
Note: On both DXLink Fiber units, the RS-232 connector pinout is “TX - RX - Ground.”
To wire the RS-232 (serial) connectors on the RX/TX for data transfer:
1.
Wire the RS-232 connectors on the units according to the pinout directly above the connector.
2. Use the command RXON to enable this port on the Transmitter and the Receiver. (For complete Serial
SEND_COMMAND programming information, see page 80.)
FIG. 19 Serial data transfer and IR flow control
FIG. 20 Wire RS-232 ports for serial data transfer
AC
DC
FLT
AC
DC
FLT
IR and/or
RS-232
Fiber optic cable
Fiber optic cable
IR and/or
RS-232
Enova DGX 16
DXLink Fiber TX
DXLink Fiber RX
RS-232 (serial) connector pinout
TXD
RXD
GND
- Instruction Manual 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Apache License, Version 2.0 10
- Warnings and Cautions 11
- Applicability Notice 12
- Product Notes 13
- Product Compatibility 15
- Common Applications 17
- Power Jack 18
- Video In Connector 18
- Overview DXLink Fiber, Duplex 19
- Fiber Optic Transceiver 20
- Common Features/Functionality 23
- DXLink Fiber Receiver, Duplex 24
- HID Devices and Windows 8 24
- 4. Click OK 25
- DXLink Fiber Specifications 28
- qualified): 1 per unit 29
- HDMI Specifications 30
- Analog Video Specifications 32
- Local Audio Specifications 33
- Installation and Setup 34
- Setup Information 35
- Example 36
- Endpoint/ 36
- Bidirectional 36
- Example B 37
- Example C 37
- Example A 37
- DIP Switch Location 38
- Setting DIP Switch #2 39
- Setting DIP Switch #4 39
- V Style mounting hardware 40
- Audio Type Precedence 42
- ICS LAN 10/100 LEDs 42
- ID Pushbutton Functions 49
- To set the Scaling Mode: 50
- Bypass Mode 50
- Auto Mode 50
- Manual Mode 50
- Persistence of Scaling Mode 51
- Network Configuration 54
- TCP/IP Address Configuration 55
- Factory Default Parameters 56
- Device IDs 57
- Using the ID Pushbutton 57
- Factory Parameters* 59
- IRL File Transfers 61
- Transferring IRL Files 63
- Additional Documentation 65
- Additional IRL Information 65
- Device Numbering and Ports 66
- VIDOUT_SCALE 68
- Scaling Modes 68
- VIDOUT_RES_REF 68
- SEND_COMMAND 68
- VI<input>O 71
- <output> 71
- VIDIN_EDID 73
- IR CHANNELs 76
- IR SEND_COMMANDs 76
- AUDIN_FOR 76
- CH SEND_COMMAND 77
- XCH SEND_COMMAND 78
- USB SEND-COMMANDs (Receiver) 82
- PERSISTAV 84
- SEND_STRING Escape Sequences 85
- Troubleshooting 86
- Network Setup Issues 87
- DXLink Fiber Troubleshooting 87
- Technical Support 88
- Important Upgrade Information 90
- Transferring KIT Files 91
- Firmware Versions 92
- Example: 93
- Telnet Username and Password 94
- Telnet Commands (continued) 100
- Guidelines 108
- TCP vs. UDP 108
- URL vs. NDP vs. Auto 109
- Windows Client Programs 109
- Linux Telnet Client 109
- Creating a Virtual Master 112
- CONNECTION and press Enter 115
- Overview 116
- HDMI Connector Cable Pinout 116
- HD-15 Connector Cable Pinout 117
- DVI Cable Connector Pinout 118
- CEA (RGB Color Space): 123
- CVR (RGB Color Space): 124
- CVT (RGB Color Space): 125
- DMR (RGB Color Space): 126
- DMT (RGB Color Space): 126
- DXLink Fiber and EDID 130
- USER EDID 1 131
- USER_EDID_MODIFIED 131
- MIRROR OUT 1 131
- MIRROR_OUT_LOCAL 131
- AMX EDID Library 131
- Software Installation on PC 132
- DXLink Fiber Connection to PC 133
- EDID Programmer tab 133
- EDID Programmer View 134
- Read Error Message 136
- 02/28/14 137
Produits connexes et manuels pour Équipement musical supplémentaire AMX DXLink Multi-Format SMF-D
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.838 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels