AMX AVS-OP-2020-117 Manuel d'instructions Page 87
- Page / 167
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
HDMI I/O Board
81
Optima Instruction Manual
Possible Solutions
One thing to try is to use the EDID Programmer to read the EDID from the destination device (see
page 158) and to write it to the Optima 8x8 HDMI input (see page 159).
Another thing to try is to use the EDID Programmer to write an EDID that best represents the
downstream destination to the HDMI input connector. Check the “EDID Library” file at www.amx.com
(search for EDID Library) to determine if one of the custom EDID files (which are variants of base
EDIDs) meets your needs. For additional information on custom EDID files, see page 160.
Initializing InstaGate
®
Technology
InstaGate
®
technology significantly reduces latency (time required for authentication) in the matrix
switcher for HDCP negotiations with the displays in a system. The latency is typically experienced when
HDCP authenticates HDMI source and destination devices. This technology effectively “opens the gate”
by pre-authorizing the connected source and destination devices to satisfy HDCP authentication.
After the first time a sink is validated by a source, when the source is routed to that same sink, the time
required to authenticate that sink is greatly reduced and protected content is displayed with less delay.
Note: Some destination devices have a longer lag time than others between receiving a signal and
displaying that signal. Although InstaGate
®
significantly reduces latency in the matrix switcher, it
cannot reduce the inherent lag time of a device.
When the system is initially set up, each first time switch to an output must go through the lengthy
authentication process. After the initial authentication, the system “remembers” the destination device
and significantly reduces the latency.
Note: If necessary, EDID Programmer software (located on the “AMX AutoPatch CD” or at
www.amx.com) is available for re-programming the HDMI connectors (see page 155).
We recommend using either of the following procedures at installation or whenever source and/or
destination devices are changed, so that the system is primed to accept all destinations (given any
limitations on the number of sinks each source supports; see page 75).
To initialize (prime) system for InstaGate
®
technology with control panel or software:
Note: The following process can take up to as much as a minute and a half for each one-to-all
routing command to complete.* It is normal for the remaining monitors to lose content as each new
output is added.
1. Check to be sure all source and destination devices attached to the HDMI board are powered up.
2. Route each input to all of the outputs.
Or
Route each input to all of the runtime intended outputs.
* Time for initial authentication can vary noticeably for different source and destination devices.
To initialize (prime) system for InstaGate
®
technology using BCS commands:
1.
Check to be sure all source and destination devices attached to the HDMI board are powered up.
2. Plug one end of a null modem serial cable into the Control (RS-232) port on the enclosure. The
pinout for the DB-9 connector is: 5 GND to 5 GND, 2 RXD to 3 TXD, and 3 TXD to 2 RXD.
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 10
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 15
- Optima Features (continued) 16
- Optima Control Features 16
- Front View 17
- Rear View 17
- CPU/Control Board 18
- Power Receptacle 19
- Input/Output Boards 19
- Input and Output Connectors 19
- Expansion/Control Slots 19
- Optima General Specifications 20
- Configuration Information 21
- Control Options 21
- System Diagnostics 22
- Installation and Setup 23
- Unpacking 24
- Installation Recommendations 25
- DVI & HDMI additional 27
- Linking Enclosures 28
- Link Cables and Equipment 29
- Ethernet Connector LEDs 29
- External Control Options 34
- Attaching Serial Controllers 35
- Signal Types and Connectors 38
- Applying Power and Startup 39
- Control Panel Startup 40
- Serial Control Device Startup 41
- Executing a Test Switch 42
- Installation Troubleshooting 43
- Technical Support 44
- Standard Video I/O Boards 45
- Attaching Cables 47
- S-Video I/O Boards 49
- Y/c I/O Board 51
- RGBHV/HD-15 I/O Boards 59
- Standard Timing 60
- Identification 60
- HDMI I/O Board 75
- Detailed Timing Blocks 77
- Audio Data Block 78
- Supported Number of Sinks 81
- HDCP Source Device 81
- One Sink Too Many 81
- Note: Monitors are numbered 84
- System Design Considerations 85
- Control Suggestions 85
- Troubleshooting Audio 86
- Initializing InstaGate 87
- Technology 87
- be sent to a 89
- Digital Audio I/O Boards 91
- Stereo Audio I/O Boards 93
- Attaching Wires 95
- Adjusting Output Volume 96
- Adjusting Digital Input Gain 96
- (with RX Modules) 99
- Specifications 100
- Standard Timings 101
- Established Timings 101
- General Specifications 102
- Attaching Cables and Wires 103
- To connect HD-15 inputs: 104
- Destination Device (Monitor) 106
- CatPro RX Module FG1010-48-01 106
- System Setup 107
- Video Display Adjustment 108
- Optima Instruction Manual 109
- Test image adjusted for skew 110
- CatPro Troubleshooting 111
- APWeb Expansion Board 113
- The APWeb Expansion Board 114
- Cabling and Applying Power 117
- Testing the Connection 118
- XNNet Expansion Board 121
- Attaching XNNet Devices 123
- Overview 125
- System Requirements 126
- Discovering a System 128
- Navigating the Interface 129
- Multiple Signal Paths 130
- Passwords 132
- Device Discovery Support 135
- Component Identity Number 138
- Modifying Virtual Matrices 141
- Joining Virtual Matrices 142
- Creating a New Virtual Matrix 145
- Grouping Pattern Examples 149
- Sequential Grouping Pattern 150
- Removing I/O Boards 152
- 4a: Remove the side screw 153
- Remove center slide-keys (2) 154
- Adding I/O Boards 155
- Step 6 Red Note 157
- 3. Cycle power on the Optima 158
- – EDID Programmer 161
- Appendix E – EDID Programmer 164
- Serial Port Settings 165
- Increase Your Revenue 167
Produits connexes et manuels pour Commutateurs vidéo AMX AVS-OP-2020-117
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels