AMX AVS-OP-2020-117 Manuel d'instructions Page 164
- Page / 167
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix E – EDID Programmer
158
Optima Instruction Manual
Reading and Saving EDID Data from a Destination Device
Tip: The Save button in the EDID Programmer can be used to save the EDID information as an
.edid file, which can be opened as a text file (click the Open button) and edited or opened and written
to an input (click the Write button).
To read and save EDID data from a destination device:
1.
On the PC, open the EDID Programmer.
2. Connect a DVI or HDMI cable to the PC using the PC’s spare monitor port (if the PC has a DVI
port and the destination device’s port is HDMI, use a DVI-to-HDMI cable adapter; if your laptop
has an HD-15 [VGA] port, see “Using Cable Adapters” below).
3. Connect the open end of the DVI or HDMI video cable to the destination device (typically a
monitor) from which the EDID information needs to be read.
4. Click the Refresh Display List button to update the Available Displays drop down list.
5. From the Available Displays drop down list, select the destination device from which you need to
read the EDID.
6. Click the Read button to read the EDID information. The results display in the read-only area.
7. Click the Save button (select location, enter file name, and click Save).
Leave the EDID Programmer open for instructions on writing the EDID to the Optima.
8. Disconnect the DVI or the HDMI cable from the PC and from the destination device.
Available Displays drop down list – select device
Close – shuts down application; will not prompt to save
Open – an EDID file
Save – an EDID file to edit or to write to input on board
Refresh Display List – updates list after additional devices attached
Convert to Digital / Convert to Analog – converts displayed EDID data
Query AutoPatch Device – acquires enclosure’s XNNet ID address
EDID Information – data (read-only) from file or device
EDID Type – indicates digital or analog (read-only)
Read – reads EDID from selected destination device
Write – writes EDID to input on board
Communication menu – use to select PC serial port or change baud rate
Status – shows application status (read-only)
edid programmer
Target Device – select Matrix Switcher
Using cable adapters
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 10
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 15
- Optima Features (continued) 16
- Optima Control Features 16
- Front View 17
- Rear View 17
- CPU/Control Board 18
- Power Receptacle 19
- Input/Output Boards 19
- Input and Output Connectors 19
- Expansion/Control Slots 19
- Optima General Specifications 20
- Configuration Information 21
- Control Options 21
- System Diagnostics 22
- Installation and Setup 23
- Unpacking 24
- Installation Recommendations 25
- DVI & HDMI additional 27
- Linking Enclosures 28
- Link Cables and Equipment 29
- Ethernet Connector LEDs 29
- External Control Options 34
- Attaching Serial Controllers 35
- Signal Types and Connectors 38
- Applying Power and Startup 39
- Control Panel Startup 40
- Serial Control Device Startup 41
- Executing a Test Switch 42
- Installation Troubleshooting 43
- Technical Support 44
- Standard Video I/O Boards 45
- Attaching Cables 47
- S-Video I/O Boards 49
- Y/c I/O Board 51
- RGBHV/HD-15 I/O Boards 59
- Standard Timing 60
- Identification 60
- HDMI I/O Board 75
- Detailed Timing Blocks 77
- Audio Data Block 78
- Supported Number of Sinks 81
- HDCP Source Device 81
- One Sink Too Many 81
- Note: Monitors are numbered 84
- System Design Considerations 85
- Control Suggestions 85
- Troubleshooting Audio 86
- Initializing InstaGate 87
- Technology 87
- be sent to a 89
- Digital Audio I/O Boards 91
- Stereo Audio I/O Boards 93
- Attaching Wires 95
- Adjusting Output Volume 96
- Adjusting Digital Input Gain 96
- (with RX Modules) 99
- Specifications 100
- Standard Timings 101
- Established Timings 101
- General Specifications 102
- Attaching Cables and Wires 103
- To connect HD-15 inputs: 104
- Destination Device (Monitor) 106
- CatPro RX Module FG1010-48-01 106
- System Setup 107
- Video Display Adjustment 108
- Optima Instruction Manual 109
- Test image adjusted for skew 110
- CatPro Troubleshooting 111
- APWeb Expansion Board 113
- The APWeb Expansion Board 114
- Cabling and Applying Power 117
- Testing the Connection 118
- XNNet Expansion Board 121
- Attaching XNNet Devices 123
- Overview 125
- System Requirements 126
- Discovering a System 128
- Navigating the Interface 129
- Multiple Signal Paths 130
- Passwords 132
- Device Discovery Support 135
- Component Identity Number 138
- Modifying Virtual Matrices 141
- Joining Virtual Matrices 142
- Creating a New Virtual Matrix 145
- Grouping Pattern Examples 149
- Sequential Grouping Pattern 150
- Removing I/O Boards 152
- 4a: Remove the side screw 153
- Remove center slide-keys (2) 154
- Adding I/O Boards 155
- Step 6 Red Note 157
- 3. Cycle power on the Optima 158
- – EDID Programmer 161
- Appendix E – EDID Programmer 164
- Serial Port Settings 165
- Increase Your Revenue 167
Produits connexes et manuels pour Commutateurs vidéo AMX AVS-OP-2020-117
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.217 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels