AMX AVS-OP-2020-117 Manuel d'instructions Page 110
- Page / 167
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
RGBHV+Stereo to CatPro I/O Boards (with RX Modules)
104
Optima Instruction Manual
5. Turn the Adjust knob clockwise or counterclockwise, if necessary, to align the green color bars with
the red color bars.
6. Press the Adjust knob.
The LED turns blue; the module is placed in Blue Skew Adjust mode.
7. Turn the Adjust knob clockwise or counterclockwise until the blue color bars align with the red and
green color bars.
8. Press the Adjust knob.
The LED turns white; the module is placed in Volume Adjust mode.
9. Turn the Adjust knob clockwise to increase volume or counterclockwise to decrease volume.
10. Press the Adjust knob.
The LED turns off, and the module saves all of the settings.
To adjust the volume without changing the skew settings:
1.
Press the Adjust knob until the LED turns white and then complete Steps 9 and 10 above.
Tip: For optimal results on flat panel LCDs, use page 2 of the .pdf test image and press the auto-
adjust button on the panel after using the potentiometers and the Adjust knob.
LED Blinks Red and Green
If the LED alternately blinks red and green, a configuration failure has occurred.
If the blinking happens when the Adjust knob is pressed to save (Step 10), the system failed to
save the settings. Any adjustments just made are still in effect, but will be lost the next time
power is cycled. Press the Adjust knob; repeat (cycle the colors) until the LED turns off.
If the blinking happens when power is cycled, the system could not find valid settings and
reverted to the factory defined default settings. Complete Steps 2 through 10 again.
Additional fine-tuning with the potentiometers may be necessary. If undesirable display conditions
persist, see “CatPro Troubleshooting” on page 105.
FIG. 66 Test image adjusted for skew
Test Pattern for Cable Length
and Skew Compensation
NOTE: This Test Pattern must be viewed in Full Screen mode at 100%. Be sure the display
resolution matches the resolution shown in the box above in order to get accurate results when
making adjustments. If the Test Pattern has been resized since opening it, press Esc, then Ctrl+L
(full screen) followed by Ctrl+1 (100%).
1. Adjust the GAIN until the display is reasonably bright.
2. Adjust the PEAK until the black and white pattern is fairly balanced.
3. Press the Adjust knob to cycle through the Red, Green, and Blue color components. At each
color, the knob can be turned to adjust the skew delay if needed. When skew adjustments are
completed, the Red, Green and Blue color bars on this page should be perfectly aligned.
4. Press the Adjust knob (the LED turns WHITE) and turn to adjust the volume if needed.
5. Press the Adjust knob again to turn off the LED and save the settings.
6. Readjust the GAIN and PEAK to sharpen the Sample Text image below.
7. (Optional) If the destination is a flat panel LCD with an auto-adjust feature:
a. Use the up/down arrows or mouse wheel to scroll to page 2 of this Test Pattern.
b. Press the auto-adjust button on the display.
c. Once the auto-adjust is complete, scroll back to page 1 to make any final adjustments.
Ctrl+Q
to Exit
1280 x 768
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 10
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 15
- Optima Features (continued) 16
- Optima Control Features 16
- Front View 17
- Rear View 17
- CPU/Control Board 18
- Power Receptacle 19
- Input/Output Boards 19
- Input and Output Connectors 19
- Expansion/Control Slots 19
- Optima General Specifications 20
- Configuration Information 21
- Control Options 21
- System Diagnostics 22
- Installation and Setup 23
- Unpacking 24
- Installation Recommendations 25
- DVI & HDMI additional 27
- Linking Enclosures 28
- Link Cables and Equipment 29
- Ethernet Connector LEDs 29
- External Control Options 34
- Attaching Serial Controllers 35
- Signal Types and Connectors 38
- Applying Power and Startup 39
- Control Panel Startup 40
- Serial Control Device Startup 41
- Executing a Test Switch 42
- Installation Troubleshooting 43
- Technical Support 44
- Standard Video I/O Boards 45
- Attaching Cables 47
- S-Video I/O Boards 49
- Y/c I/O Board 51
- RGBHV/HD-15 I/O Boards 59
- Standard Timing 60
- Identification 60
- HDMI I/O Board 75
- Detailed Timing Blocks 77
- Audio Data Block 78
- Supported Number of Sinks 81
- HDCP Source Device 81
- One Sink Too Many 81
- Note: Monitors are numbered 84
- System Design Considerations 85
- Control Suggestions 85
- Troubleshooting Audio 86
- Initializing InstaGate 87
- Technology 87
- be sent to a 89
- Digital Audio I/O Boards 91
- Stereo Audio I/O Boards 93
- Attaching Wires 95
- Adjusting Output Volume 96
- Adjusting Digital Input Gain 96
- (with RX Modules) 99
- Specifications 100
- Standard Timings 101
- Established Timings 101
- General Specifications 102
- Attaching Cables and Wires 103
- To connect HD-15 inputs: 104
- Destination Device (Monitor) 106
- CatPro RX Module FG1010-48-01 106
- System Setup 107
- Video Display Adjustment 108
- Optima Instruction Manual 109
- Test image adjusted for skew 110
- CatPro Troubleshooting 111
- APWeb Expansion Board 113
- The APWeb Expansion Board 114
- Cabling and Applying Power 117
- Testing the Connection 118
- XNNet Expansion Board 121
- Attaching XNNet Devices 123
- Overview 125
- System Requirements 126
- Discovering a System 128
- Navigating the Interface 129
- Multiple Signal Paths 130
- Passwords 132
- Device Discovery Support 135
- Component Identity Number 138
- Modifying Virtual Matrices 141
- Joining Virtual Matrices 142
- Creating a New Virtual Matrix 145
- Grouping Pattern Examples 149
- Sequential Grouping Pattern 150
- Removing I/O Boards 152
- 4a: Remove the side screw 153
- Remove center slide-keys (2) 154
- Adding I/O Boards 155
- Step 6 Red Note 157
- 3. Cycle power on the Optima 158
- – EDID Programmer 161
- Appendix E – EDID Programmer 164
- Serial Port Settings 165
- Increase Your Revenue 167
Produits connexes et manuels pour Commutateurs vidéo AMX AVS-OP-2020-117
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels