AMX AVS-OP-2020-117 Manuel d'instructions Page 126
- Page / 167
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix A – Managing Configuration Files
120
Optima Instruction Manual
Automatic Configuration
An Optima system is automatically configured when the system generates its own configuration based
on the installed hardware (applies to some Optima single-enclosure systems). The configuration is
constructed internally with a standard set of 3 virtual matrices* by the CPU upon initial boot up of the
system.
When a system is automatically configured, the configuration information can be accessed for
modification in only one way since an .xcl file does not exist for the system. Use XNConnect to discover
the configuration information from the CPU. The discovered configuration information can then be
saved as an .xcl file. After the configuration is modified in XNConnect, it is loaded back onto the CPU
(replacing the automatically constructed configuration). If necessary, the automatically constructed
configuration can be restored (see page 129).
* The standard set of 3 virtual matrices for switching signals is VM 0 = audio-follow-video,
VM 1 = video, and VM 2 = audio.
AMX AutoPatch CD Information
If you cannot locate the AMX AutoPatch CD that shipped with your system and your AMX account has
the required permissions, you can download the newest version of XNConnect from www.amx.com.
An INI file Updater for updating XNConnect is available on the AMX website under Tech Center \
AutoPatch Tools; an account is not required. If you need an .xcl configuration file that is compatible with
your system, either discover the system (see page 122) or contact technical support (see page 38) and
provide your system’s serial number.
Installing and Launching XNConnect
Use XNConnect software only if you need to customize or change the configuration information from
the original specification.
Important: Even if XNConnect is already on your PC, install the newest version that shipped on the
“AMX AutoPatch CD” with your system. We strongly recommend uninstalling the old version of
XNConnect before installing a new version.
System Requirements
Windows XP Professional
®
233 MHz processor
Minimum of 128 MB of RAM
20 MB of available hard drive space
800x600 screen resolution (1024x768 is recommended)
Serial port and RS-232 null modem cable
FIG. 77 Example of discovery information for automatically constructed configuration
When discovered, an automatically
constructed configuration does not show
a file name
- Instruction Manual 1
- Distribution Matrix 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 10
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 15
- Optima Features (continued) 16
- Optima Control Features 16
- Front View 17
- Rear View 17
- CPU/Control Board 18
- Power Receptacle 19
- Input/Output Boards 19
- Input and Output Connectors 19
- Expansion/Control Slots 19
- Optima General Specifications 20
- Configuration Information 21
- Control Options 21
- System Diagnostics 22
- Installation and Setup 23
- Unpacking 24
- Installation Recommendations 25
- DVI & HDMI additional 27
- Linking Enclosures 28
- Link Cables and Equipment 29
- Ethernet Connector LEDs 29
- External Control Options 34
- Attaching Serial Controllers 35
- Signal Types and Connectors 38
- Applying Power and Startup 39
- Control Panel Startup 40
- Serial Control Device Startup 41
- Executing a Test Switch 42
- Installation Troubleshooting 43
- Technical Support 44
- Standard Video I/O Boards 45
- Attaching Cables 47
- S-Video I/O Boards 49
- Y/c I/O Board 51
- RGBHV/HD-15 I/O Boards 59
- Standard Timing 60
- Identification 60
- HDMI I/O Board 75
- Detailed Timing Blocks 77
- Audio Data Block 78
- Supported Number of Sinks 81
- HDCP Source Device 81
- One Sink Too Many 81
- Note: Monitors are numbered 84
- System Design Considerations 85
- Control Suggestions 85
- Troubleshooting Audio 86
- Initializing InstaGate 87
- Technology 87
- be sent to a 89
- Digital Audio I/O Boards 91
- Stereo Audio I/O Boards 93
- Attaching Wires 95
- Adjusting Output Volume 96
- Adjusting Digital Input Gain 96
- (with RX Modules) 99
- Specifications 100
- Standard Timings 101
- Established Timings 101
- General Specifications 102
- Attaching Cables and Wires 103
- To connect HD-15 inputs: 104
- Destination Device (Monitor) 106
- CatPro RX Module FG1010-48-01 106
- System Setup 107
- Video Display Adjustment 108
- Optima Instruction Manual 109
- Test image adjusted for skew 110
- CatPro Troubleshooting 111
- APWeb Expansion Board 113
- The APWeb Expansion Board 114
- Cabling and Applying Power 117
- Testing the Connection 118
- XNNet Expansion Board 121
- Attaching XNNet Devices 123
- Overview 125
- System Requirements 126
- Discovering a System 128
- Navigating the Interface 129
- Multiple Signal Paths 130
- Passwords 132
- Device Discovery Support 135
- Component Identity Number 138
- Modifying Virtual Matrices 141
- Joining Virtual Matrices 142
- Creating a New Virtual Matrix 145
- Grouping Pattern Examples 149
- Sequential Grouping Pattern 150
- Removing I/O Boards 152
- 4a: Remove the side screw 153
- Remove center slide-keys (2) 154
- Adding I/O Boards 155
- Step 6 Red Note 157
- 3. Cycle power on the Optima 158
- – EDID Programmer 161
- Appendix E – EDID Programmer 164
- Serial Port Settings 165
- Increase Your Revenue 167
Produits connexes et manuels pour Commutateurs vidéo AMX AVS-OP-2020-117
(26 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels