AMX AVB-WP-TX-MULTI-DXLINK Manuel d'instructions Page 68
- Page / 154
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation and Setup
62
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Downloading Firmware State and LED Behavior
To monitor the state of a module by its LEDs when downloading firmware, check both the Link/Act and
Status LED columns.
DXLink TX/RX in a Multiple-Stage Switching System
When switching systems with DXLink Technology support (e.g., an Enova DGX Digital Media
Switcher and an Enova DVX-3155HD) are connected via their DXLink ports, DXLink Transmitters and
Receivers can be used to extend the video and audio transport.
Important: This section does not refer to the linking of enclosures from CPU to CPU, which is not
supported in the Enova DGX Digital Media Switcher or the Enova DVX Solutions.
In an installation with DXLink equipment in a multiple-stage switching system, the following apply:
Network loops must be avoided (see page 40). The DXLink line’s Ethernet functionality is
disabled between the enclosures; therefore, no IR, serial, or Ethernet communication can be
passed between them.
When two switching systems with DXLink support are connected via their DXLink ports,
only video and audio will be passed through the DXLink connection.
When a DXLink input or output on one switching system determines that it is connected to a
DXLink input or output on another switching system, the DXLink port will automatically
disable all Ethernet, power, and control on that connection port so that the only things passed
down the DXLink line are the video and audio signals.
When connecting switching systems via DXLink ports, AMX recommends no more than
three switcher throughputs (see the “Example” below).
Example
This example shows how DXLink Transmitters and Receivers can be used in a system where switchers
are connected via their DXLink ports.
The signal path through three switchers could be: source device
DXLink Transmitter
Enova DVX-3155HD, DXLink input (out a DXLink output)
Enova DGX 32, DXLink input (out a
DXLink output)
Enova DGX 16, DXLink input (out a DXLink output) DXLink Receiver
display device as an HDMI signal.
NetLinx LED Behavior when Downloading Firmware
Downloading Firmware Link/Act LED Status LED
Downloading firmware to flash due to an
upgrade via NetLinx Studio.
Fast blink, alternating with
Status LED
Fast blink, alternating with Link/Act
LED
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 7
- Copyright Notice 10
- Liability Notice 10
- US FCC Notice 10
- Lithium Batteries Notice 11
- Trademark Notices 11
- Warnings and Cautions 11
- Applicability Notice 13
- Product Notes 13
- Product Compatibility Tables 14
- Common Applications 16
- Transmitters 16
- Multi-Format TX front view 16
- HDMI TX front view 16
- (Blinking = #3 Toggle OFF) 17
- Multi-Format TX rear view 21
- HDMI TX rear view 21
- Receiver 24
- HDMI RX front view 24
- HDMI RX rear view 25
- Common Features/Functionality 27
- HDCP Compliance 28
- General Specifications 31
- Shielded Cat6, Cat6A, Cat7* 32
- qualified): 1 per module 33
- Audio Format 34
- Analog Video Specifications 36
- Local Audio Specifications 37
- Installation and Setup 39
- Setup Information 40
- Example B 43
- Example C 43
- Example D 43
- Example A 43
- DXLink connections 44
- Avoid network loops 46
- V Style mounting hardware 50
- ICS LAN 10/100 LEDs 54
- (modules only) 54
- NetLinx LEDs 55
- DXLink LEDs 55
- Audio Type Precedence 56
- Important: Do not 57
- Rear view 57
- Front view 57
- HDMI RX – Applying Power 62
- IR Receiver cable (FG-IR03) 64
- ID Pushbutton Functions 65
- Manual Mode 66
- DXLink Transmitter 68
- Network Configuration 69
- TCP/IP Address Configuration 70
- Factory Default Parameters 71
- Device IDs 72
- Using the ID Pushbutton 72
- LED columns 77
- IRL File Transfers 79
- Transferring IRL Files 82
- Additional Documentation 84
- Device Numbering and Ports 85
- Overview 85
- CHANNELs 87
- Aspect Ratio Options 89
- VIDIN_PREF_EDID 93
- IR SEND_COMMANDs 97
- GET MODE 98
- Serial SEND_COMMANDs 101
- DXLink System SEND_COMMANDs 104
- SEND_STRING Escape Sequences 105
- Troubleshooting 107
- Determining HDCP Compliance 108
- Power Issues 108
- DXLink Connection Issues 109
- Network Setup Issues 110
- Technical Support 110
- Extender System (Standalone) 111
- Important Upgrade Information 114
- Transferring KIT Files 115
- Telnet Username and Password 118
- Telnet Commands (continued) 120
- Master Connection Modes 125
- Windows Client Programs 126
- Linux Telnet Client 126
- Receivers is 192.168.1.2) 127
- Creating a Virtual Master 129
- Click to open the 129
- Communication Settings 129
- CONNECTION and press Enter 132
- HD-15 Connector Cable Pinout 134
- DVI-I signal is required 135
- SEND_COMMANDs 141
- CEA (RGB Color Space): 142
- CVR (RGB Color Space): 143
- CVT (RGB Color Space): 144
- DMR (RGB Color Space): 145
- DMT (RGB Color Space): 145
- Applicability 147
- Remove jackscrew and washer 148
- Appendix H – EDID Programming 149
- DXLink Connection to PC 150
- EDID Programmer View 151
- 06/20/13 154
Produits connexes et manuels pour Émetteurs muraux AMX AVB-WP-TX-MULTI-DXLINK
(24 pages)Samsung ME1040WE manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Samsung ME1040WE.
Nous fournissons des manuels en pdf 1 Samsung ME1040WE à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels