AMX RE-DM6 Spécifications Page 36
- Page / 90
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Radia Lighting System Configuration Pages
28
RE-DM4 and RE-DM6 RADIA Eclipse Dimmer Modules
To modify an existing preset:
1. In the Device Configuration page, scroll down to the preset to be modified.
2. For more information on the preset, click the Info button for the preset. This opens a new information box
with the preset’s dimmer and level information.
When finished, close the box.
3. In the Label field, change the preset’s label if necessary.
4. Select the Preset Time by either moving the slidebar or entering the preset time (1-255) in the field to the
right of the slidebar.
If you enter a preset time number higher than 255, the slidebar will move to the "Max" position.
5. To configure the preset, click the preset’s Configure button to open the Preset Configuration page
(FIG. 33).
When finished, click the Accept button at the bottom of the page and return to the Device Configuration
page.
To return to the Device Configuration page without saving any changes, click the Cancel button.
FIG. 32 Presets section
- Radia Eclipse Dimmer 1
- Table of Contents 5
- Radia Eclipse Dimmer Modules 9
- RE-DM4 Specifications 10
- Suggested Loads 10
- Line-In Connections 11
- RE-DM6 Specifications 14
- Suggested Installation Loads 14
- AMX Lighting Systems 17
- Installation 19
- LEFT SIDE FRONT RIGHT SIDE 20
- SIDE VIEW 21
- RDA-ENC6B 21
- TOP VIEW 21
- High-Voltage Connections 23
- Connect to neutral block 24
- Low-Voltage Connections 28
- Position Value 30
- Connecting Dry Closures 31
- Failsafe Input 31
- Emergency Input 31
- Default Settings 32
- Overview 33
- Lighting System Link 33
- Main Lighting System Page 34
- Device Configuration Page 35
- FIG. 32 Presets section 36
- FIG. 34 New Preset button 37
- Software 39
- Preset Status 40
- Lighting Systems Overview 41
- Programming Commands 42
- Channels 44
- SEND_STRINGs 44
- Ramp Dimmers Up 45
- Ramp Dimmers Down 45
- Stop Ramping Dimmer 46
- Ramp Active Preset Up 46
- Ramp Active Preset Down 46
- Stop Ramping Preset 47
- Recall Preset 47
- Record Preset 47
- Level Status 47
- Set Curve 48
- Curve Status 48
- Set Low End 48
- Low End Status 48
- Dimmer Status 49
- Set Default Level Time 49
- Set Default Preset Time 49
- Set Default Ramp Time 50
- Ramp To Level 50
- Undefine Dimmer 50
- Phase Query 51
- Version Query 51
- Factory Default 51
- SEND_COMMANDs 52
- Ramp Preset Down (NEW) 53
- Stop Ramping Preset (NEW) 53
- Curve Status (NEW) 54
- Set Low End (NEW) 54
- Low End Status (NEW) 54
- Reboot (NEW) 54
- Ramp to Level 55
- Undefine Dimmer (NEW) 55
- Phase Query (NEW) 56
- FIG. 38 Basic dimming curve 58
- Curve Configuration 59
- Standard Dimming Curve (1) 60
- Economical Dimming Curve (2) 62
- 0-10VDC Curve (3) 63
- Curve 3 at 120 VAC 64
- Curve 3 at 240 VAC 64
- Curve 3 output in volts DC 64
- 0-12VDC Curve (4) 65
- Lutron FDB Curve (5) 66
- FIG. 56 Curve 5 at 240 VAC 67
- Advance Mark VII Curve (6) 68
- 12% Roll Off (7) 69
- 19% Roll Off (8) 71
- 33% Roll Off (9) 72
- S-Curve #1 (A) 74
- Log-Curve #1 (B) 75
- Log-Curve #2 (C) 77
- S-Curve #2 (D) 78
- 10% Off Curve (N) 79
- Always OFF Curve (O) 80
- Always ON Curve (F) 81
- Curve F at 240 VAC 82
- Curve R at 120 VAC 83
- Curve R at 240 VAC 83
- Curves 5 & B at 120 VAC 83
- Curves 6 & C at 120 VAC 84
- Curves A & D at 120 VAC 85
- Curves A & D at 240 VAC 85
- Appendix B: Troubleshooting 87
- Hardware Issues 88
- Increase Your Revenue 90
Sony SVS1313ZDZB Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Powerbanks Sony SVS1313ZDZB.
Wir stellen 1 PDF-Handbücher Sony SVS1313ZDZB zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Schnellstart Benutzerhandbuch
Commentaires sur ces manuels