AMX DXLink Multi-Format Wallplate Manuel d'instructions Page 114
- Page / 141
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Appendix B – Telnet (Terminal) Commands
114
Instruction Manual – DXLink™ Twisted Pair Transmitters/Receiver
Telnet Commands (continued)
SET ETHERNET MODE This command sets the current LAN configuration settings per new mode.
Syntax:
SET ETHERNET MODE <newmode>
Values for newmode are:
auto
Or
10 full, 100 full, 10 half, or 100 half
Note: This command requires a reboot to enable new settings.
Examples:
set ethernet mode auto
set ethernet mode 100 full
Note: See GET ETHERNET MODE on page 112.
SET FRIENDLY Set the device’s friendly name for NDP to <name>.
Syntax:
SET FRIENDLY <name>
• Maximum length = 25 characters. If the name entered exceeds 25 characters, it will be
truncated.
• The value is stored in non-volatile memory.
• If no value specified, an automatic name consisting of AMX, the product name, and serial
number will be used.
Note: This command requires a reboot to enable new settings.
SET IP Sets the IP configuration of a specified device.
Enter a Host Name, Type (DHCP or Fixed), IP Address, Subnet Mask, and Gateway
IP Address.
Note: DHCP implies “DHCP with link-local fallback”.
Note: For NetLinx Masters, the Host Name can only consist of alphanumeric characters.
• Enter Y (yes) to approve/store the information into the Master.
• Enter N (no) to cancel the operation.
Note: This command requires a reboot to enable new settings.
Example:
>SET IP
--- Enter New Values or just hit Enter
to keep current settings ---
Enter Host Name: MLK_INSTRUCTOR
Enter IP type. Type D for DHCP or S for Static IP and
then Enter: DHCP
You have entered: Host Name MLK_INSTRUCTOR
Type DHCP
Is this correct? Type Y or N and Enter -> y
Settings written. Device must be rebooted to enable
new settings.
Note: DXLink Modules can also be set to Static IP or DHCP Mode via the front panel
ID Pushbutton.
SET LOCATION Sets the location parameter for NDP.
Syntax:
SET LOCATION <location>
• Maximum length = 25 characters. If the name entered exceeds 25 characters, it will be
truncated.
Note: This command requires a reboot to enable new settings.
- Twisted Pair 1
- Transmitters/Receiver 1
- Contents 3
- ESD Warning 6
- Copyright Notice 9
- Liability Notice 9
- US FCC Notice 9
- Lithium Batteries Notice 9
- Trademark Notices 9
- Warnings and Cautions 10
- Applicability Notice 11
- Product Notes 11
- Product Compatibility Tables 12
- Multi-Format TX front view 14
- HDMI TX front view 14
- Multi-Format TX rear view 18
- HDMI TX rear view 19
- Receiver 22
- HDMI RX front view 22
- HDMI RX rear view 23
- Common Features/Functionality 25
- USB Port (Rear) 26
- Shielded Cat6, Cat6A, Cat7* 31
- qualified): 1 per module 32
- Audio Format 33
- Local Audio 35
- Specifications 35
- Installation and Setup 36
- Setup Information 37
- Custom EDID Settings 38
- Example B 40
- Example C 40
- Example D 40
- Example A 40
- Power Budget Calculation 42
- Avoid network loops 43
- #1 Toggle Settings 44
- Installation Options 44
- #2 Toggle Settings 44
- #3 Toggle Settings 45
- V Style mounting hardware 46
- DXLink LEDs 51
- Audio Type Precedence 52
- Control Cables 55
- HDMI RX – Applying Power 58
- IR Receiver cable (FG-IR03) 60
- ID Pushbutton Functions 61
- Network Configuration 64
- TCP/IP Address Configuration 65
- Factory Default Parameters 66
- Device IDs 67
- Using the ID Pushbutton 67
- Factory Parameters* 69
- IRL File Transfers 72
- Transferring IRL Files 75
- Additional Documentation 77
- Overview 78
- Device Numbering and Ports 78
- Aspect Ratio Options 82
- VIDIN_PREF_EDID 85
- IR CHANNELs 88
- IR SEND_COMMANDs 88
- GET MODE 89
- SET MODE (IR command) 90
- USB SEND-COMMANDs (Receiver) 94
- FACTORYAV command 96
- SET TELNET PORT 97
- Troubleshooting 99
- Power Issues 100
- DXLink Connection Issues 101
- Network Setup Issues 102
- Technical Support 102
- Extender System (Standalone) 103
- Important Upgrade Information 105
- Firmware Versions 106
- Transferring KIT Files 107
- Telnet Username and Password 109
- Telnet Commands (continued) 111
- Master Connection Modes 116
- Windows Client Programs 117
- Linux Telnet Client 117
- Creating a Virtual Master 120
- Click to open the 120
- Communication Settings 120
- CONNECTION and press Enter 122
- HD-15 Connector Cable Pinout 124
- DVI Connector Pinout 125
- CEA (RGB Color Space): 130
- CVR (RGB Color Space): 131
- CVT (RGB Color Space): 132
- DMR (RGB Color Space): 133
- DMT (RGB Color Space): 133
- Applicability 134
- Remove jackscrew and washer 135
- Appendix H – EDID Programming 136
- DXLink Connection to PC 137
- EDID Programmer View 138
- Read Error Message 139
- 01/07/14 141
Produits connexes et manuels pour Récepteur AMX DXLink Multi-Format Wallplate
Récepteur AMX MX8 Manuel d'instructions
(22 pages)
(22 pages)
Récepteur AMX MX16 Manuel d'utilisateur
(2 pages)
(2 pages)
Récepteur AMX MX8 Manuel d'utilisateur
(2 pages)
(2 pages)
(6 pages)Samsung ME1040WE manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Samsung ME1040WE.
Nous fournissons des manuels en pdf 1 Samsung ME1040WE à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels