AMX NI-3100 Spécifications Page 98
- Page / 160
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
NetLinx Programming
88
NetLinx Integrated Controllers- WebConsole & Programming Guide (FMv3)
IR/Serial SEND_COMMANDs (Cont.)
Command Description
CH
Send IR pulses for the
selected channel.
All channels below 100 are transmitted as two digits. If the IR code for ENTER
(function #21) is loaded, an Enter will follow the number. If the channel is
greater than or equal to (>=) 100, then IR function 127 or 20 (whichever exists)
is generated for the one hundred digit. Uses 'CTON' and 'CTOF' times for pulse
times.
Syntax:
SEND_COMMAND <DEV>,"'CH',<channel number>"
Variable:
channel number = 0 - 199.
Example:
SEND_COMMAND IR_1,"'CH',18"
This device performs the following:
• Transmits IR signals for 1 (IR code 11). The transmit time is set with the
CTON command.
• Waits until the time set with the CTOF command elapses.
• Transmits IR signals for 8 (IR code 18).
• Waits for the time set with the CTOF command elapses. If the IR code for
Enter (IR code 21) is programmed, the Controller performs the following
steps.
1) Transmits IR signals for Enter (IR code 21).
2) Waits for the time set with the CTOF command elapses.
CP
Halt and Clear all active or
buffered IR commands, and
then send a single IR pulse.
You can set the Pulse and Wait times with the 'CTON' and 'CTOF' commands.
Syntax:
SEND_COMMAND <DEV>,"'CP',<code>"
Variable:
code = IR port's channel value 0 - 252 (253 - 255 reserved).
Example:
SEND_COMMAND IR_1,"'CP',2"
Clears the active/buffered commands and pulses IR_1 port's channel 2.
CTOF
Set the duration of the Off
time (no signal) between IR
pulses for channel and IR
function transmissions.
Off time settings are stored in non-volatile memory. This command sets the
delay time between pulses generated by the 'CH' or 'XCH' send commands in
tenths of seconds.
Syntax:
SEND_COMMAND <DEV>,"'CTOF',<time>"
Variable:
time = 0 - 255. Given in 1/10ths of a second. Default is 5 (0.5 seconds).
Example:
SEND_COMMAND IR_1,"'CTOF',10"
Sets the off time between each IR pulse to 1 second.
CTON
Set the total time of IR pulses
transmitted and is stored in
non-volatile memory.
This command sets the pulse length for each pulse generated by the 'CH' or
'XCH' send commands in tenths of seconds.
Syntax:
SEND_COMMAND <DEV>,"'CTON',<time>"
Variable:
time = 0 - 255. Given in 1/10ths of a second. Default is 5 (0.5 seconds).
Example:
SEND_COMMAND IR_1,"'CTON',20"
Sets the IR pulse duration to 2 seconds.
- Last Revised: 5/25/2012 1
- Table of Contents 10
- About This Document 12
- Related Documents 13
- Using Zero Configuration 14
- Before You Start 15
- Device Addressing dialog 16
- WebConsole UI Overview 31
- Device Tree 32
- Device Network Settings Pages 33
- ZeroConfig Networking 34
- WebConsole - Security Options 35
- Login Rules 36
- User Name and Password Rules 36
- Allowed Special Characters 36
- Security - System Level 37
- Access Options 38
- Accepting Changes 39
- Configuring Settings 39
- System Security - Group Level 40
- Group Security Details Page 42
- System Security - User Level 44
- Deleting a User 46
- Compression Options 47
- WebConsole - System Options 49
- Diagnostic Options table 54
- Edit Options window 56
- Port Settings 59
- Server Port Settings 59
- SSL Certificate Options 61
- SSL Certificate Entries 62
- Import SSL Certificate window 64
- System - Manage License 68
- System - Manage NetLinx 69
- System - Manage Devices 71
- Manage Devices - Bindings 73
- Adding a User-Defined Device 77
- Editing Polled Port Settings 80
- Manage Devices - URL List 82
- Manage Devices - Log 85
- Manage Devices - Diagnostics 86
- NetLinx Programming 89
- Master SEND_COMMANDs (Cont.) 90
- Port: System 91
- RS232/422/485 Ports Channels 92
- IR / Serial Ports Channels 97
- IR RX Port Channels 97
- IR/Serial SEND_COMMANDs 97
- Input/Output SEND_COMMANDs 103
- I/O SEND_COMMANDs (Cont.) 104
- Overview 105
- Terminal Commands 107
- Terminal Commands (Cont.) 108
- ESC Pass Codes 125
- Setup Security Menu 127
- Security Options Menu 128
- Edit User Menu 129
- Edit Group Menu 129
- Telnet Diagnostics Commands 132
- Linux Telnet Client 133
- IPSec Config file 135
- Internet Key Exchange (IKE) 135
- SpdAddTunnel 138
- SpdAddBypass 139
- SpdAddDiscard 139
- SpdSetProp 140
- SpdSetProp (Cont.) 141
- SpdSetPropAttrib 143
- Manual Key Manager (MKM) 145
- IPSec Security Settings page 153
- Programming API 155
- CLKMGR_GET_ACTIVE_TIMESERVER 156
- (CONSTANT CHAR RECORD[]) 157
- Increase Your Revenue 160
Produits connexes et manuels pour Passerelles/contrôleurs AMX NI-3100
(40 pages)Samsung ME1040WE manuels
Manuels d'utilisation et guides de l'utilisateur pour Non Samsung ME1040WE.
Nous fournissons des manuels en pdf 1 Samsung ME1040WE à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels