AMX MAX-MMS-400 Guide d'installation télécharger pdf

Installation Guide

MAX MDL200 Multi-Disc Loader

MDL200 Multi Disc Loader

The MDL200 Multi Disc Loader (FIG. 1) allows you to bulk-rip up to 200 discs (DVD or

CD), and load the content on a MMS server. The MDL200 comes as a kit that includes

a laptop PC pre-loaded with all required software, and pre-configured for plug and play

operation. The MDL200 has three IEEE1394 (FireWire) ports for communication with

the laptop (see FIG. 1), and includes all cables necessary to get started.

To use the MDL200, you’ll connect the MDL200 to the laptop PC and to the target

MMS server as described in this document. The BulkRipper software application (pre-

loaded on the laptop) allows you to specify an IP address for the target MMS server,

and manage the MDL200 and the bulk-ripping process.

Refer to the MDL200 & BulkRipper Instruction Manual (available online at

www.amx.com) for a detailed description of the MDL200, the Bulkripper application,

and additional information on using Bulkripper to load discs to the MMS server.

MDL200 Product Specifications

Step 1: Connect the MDL200 to the MMS Server and Laptop PC

The MDL200 first needs to be connected to the laptop PC and the MMS server that

you will be loading the media to, as described below.

1. Connect one of the IEEE 1394 ports on the rear of the MDL200 to the IEEE 1394

port on the laptop PC, using the included IEEE 1394 cable.

2. Connect the laptop PC to the MMS server, either with a direct connection or via a

LAN:

Direct Connection (recommended method)

Use the included Ethernet crossover cable to connect the PC directly to the MMS

server’s ETHERNET CONTROL port (FIG. 2).

3. Connect the MMS server’s power cable(s).

4. Power up the MDL200, laptop PC and MMS server, allowing up to one minute for

the server to boot up.

Note: Alternatively, you can also connect the laptop PC to the MMS server via a LAN

connection. Refer to the MDL200 & BulkRipper Instruction Manual (available online at

www.amx.com) for details. Using the MDL200 on a LAN connection may result in slow

loading, due to network configuration and the amount of network traffic.

Step 2: Verifying Communication Between the PC, MDL200 and MMS

Once the MDL200, laptop PC and MMS server are connected and powered up:

1. Launch the BulkRipper application on the laptop PC. BulkRipper is the software

(already loaded and configured on the laptop PC) that manages the process of

loading discs into the MDL200 and loading the media to a target MMS server.

Double-click the BulkRipper desktop icon to launch the program and access the

main window (FIG. 3).

Refer to the MDL200 Multi-Disc Loader and BulkRipper Software Instruction

Manual for a detailed description of the BulkRipper application.

2. The laptop PC and the BulkRipper application are pre-configured to allow com-

munication between the PC, the MDL200. The status bar should indicate that

you have successfully connected to the MDL200 and the MMS server (see

FIG. 3). The center area of the status bar should indicate that the MDL200

(Powerfile-C200) is connected and running, and the MMS icon on the right side

of the status bar should be green to indicate communication with the server.

If you are not communicating with either the MDL200 or the MMS server, first

verify that your cables are connected properly. Then select File > Settings (in

BulkRipper) to open the Settings dialog:

a. Verify that the Max MMS/IMS IP address indicated here matches that of the

target MMS server (default = 192.168.1.30).

b. Verify that the Changer Number field is set to “Changer 1”. In the event that

you are using more than one MDL200, use this drop-down menu to select

the source MDL200 for this load operation.

3. Click OK to save your changes and close the Settings dialog.

Once the status bar indicates that you are connected to both the MDL200 and the

MMS server, then you are ready to load discs (DVDs and CDs) into the MDL200.

DVD Region Code Settings on the MDL200

The MDL200 has two internal DVD-ROMs, each of which may require that you specify

a DVD region code setting different than the default setting of Region 1. Note that you

can set the region code on each drive, and you may choose to specify different region

codes for each one. Refer to the insert regarding changing region code settings on

MAX DVD-ROMs, included with the MDL200 for details and instructions.

Step 3: Loading Discs Into the MDL200

Discs are physically loaded into the MDL200 through the vertical disc tray slot on the

front panel of the unit (see FIG. 1), using the Chapter > Load All options in Bulkripper.

For best results, discs should be loaded contiguously (avoid leaving empty slots

between discs).

FIG. 1 MAX MDL200 Multi Disc Loader (front and rear panel components)

MDL200 (FG 2179-01) Specifications

Storage Capacity: 200 discs, 4.7 GB/disc

Power Requirements: • Voltage: 110 – 240V AC (autosensing)

• Frequency: 50/60 Hertz

• Consumption: 45 watts (peak), 35 watts (normal)

AC Current Draw (AMP): • .45A - Bootup/Power Cycle Peak

• .45A - Normal Usage Peak

Interface Specifications

(IEEE 1394):

• Bus interface IEEE-1394 compliant

• Data transfer rate 100, 200, and 400Mbps

• Three 6-pin IEEE-1394 ports

DVD-ROM drives: Two DVD-ROM drives (both drives can rip discs simultaneously)

Drive Specifications: • Supports most popular CD & DVD formats (DVD-RAM, DVD-RW

and DVD+ are not supported).

• Random seek: 90 ms (DVD-ROM); 80 ms (CD-ROM)

• Random access: 110 ms (DVD-ROM); 85 ms (CD-ROM)

• Data Transfer Rate:

- Sustained DVD 8,112KBps (6x)

- CD (Mode 1) 4,800KBps (32x)

- CD (Mode 2) 5,475KBps (32x)

Front Panel Components: • Power switch

•Disc tray

• Transport Control buttons and Display: When used with the laptop

PC that comes with the MDL200 (pre-configured with the

BulkRipper application), there is no need to use these front-panel

controls. Instead, use the controls provided in BulkRipper.

Rear Panel Connectors: • Three IEEE 1394 ports

• Power Cable connector: IEC connector for AC power cable.

Reliability: • Mechanism MTBF: 1,000,000 swaps

• Power On Hours: 100,000

Operating Environment: • Operating Temperature: 5° to 40° C; 41° to 104° F

• Storage Temperature: -10° to 60° C; 14° to 140° F

• Operating Humidity: 10% - 90% relative humidity

• Storage Humidity: 5% - 95% relative humidity, non-condensing

Average Disc to Disc

Access Time:

4 seconds

IEEE 1394 ports

Power cable connector

(rear)

Power button

Disc loading slot

(front)

(insert discs

here to load the

internal carousel).

Do not use the external transport control

pushbuttons - use the controls provided

in the BulkRipper software application instead.

MDL200 Specifications (Cont.)

Data Transfer Rate: • Sustained DVD 8,112KBps (6x)

• CD (Mode 1) 4,800KBps (32x)

• CD (Mode 2) 5,475KBps (32x)

Dimensions (HWD): 8 3/4" x 17” x 20" (22.22cm x 43.18cm x 50.80cm)

Weight: 30 lbs (13.60 kg)

Included Accessories: • Laptop PC (P4 with IEEE 1394 capabilities, configured with

BulkRipper software for managing the MDL200.

• 6’ (1.83m) IEEE 1394 cable

• 6’ (1.83m) Ethernet Crossover cable

• 6’ (1.83m) AC Power cable

FIG. 2 Example configuration - direct connection

Ethernet Crossover Cable (included)

MDL200

Laptop PC

IEEE 1394

cable

MMS Server

1 2

MAX MDL200 Multi-Disc Loader 1

Résumé du contenu

Page 1 - MAX MDL200 Multi-Disc Loader

Installation GuideMAX MDL200 Multi-Disc LoaderMDL200 Multi Disc LoaderThe MDL200 Multi Disc Loader (FIG. 1) allows you to bulk-rip up to 200 discs (DV

Page 2

AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Man

Commentaires sur ces manuels

Pas de commentaire

AMX MAX-MMS-400 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Non AMX MAX-MMS-400. AMX MAX-MMS-400 Installation guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non AMX MAX-MMS-400