AMX CSG-580 Guide d'installation télécharger pdf

Installation Guide

CSG SIP Communications Gateway (CSG-500/544/580)

ATTENTION: READ THIS FIRST!

For more detailed installation, configuration, programming, and operating

instructions, refer to the CSG SIP Communications Gateway Instruction Manual

available on-line at www.amx.com.

FIG. 1 CSG SIP Communications Gateway (displaying CSG-544)

Overview

The CSG SIP Communications Gateway (FIG. 1) is a stand alone Private Branch

Exchange (PBX) which runs a version of Asterisk. The CSG can function not

only as a PBX, but also as VoIP ATA, or VoIP gateway. It has eight analog ports

that can be configured (via modules) as Foreign Exchange Office (FXO) or

Foreign Exchange Station (FXS) ports.

The CSG enables you to transform an intercom-enabled Modero Touch Panel

into a full-featured IP phone. With the CSG and an intercom-enabled Modero

Touch Panel you can make and receive local, long distance, and international

phone calls, and have access to phone features like call waiting, caller ID, call

forwarding, call queuing, and voice mail. The CSG supports AMX Session

Initiated Protocol (SIP)-enabled touch panels, such as the MVP-8400i,

NXD-1000Vi, and NXD-700Vi, as well as 3rd party IP phones.

Specifications

Installing the Hardware

CAUTION!

To reduce the risk of fire, use only No. 26 AWG or larger

telecommunication wiring for network connections.

1. Connect an Ethernet cable to the Network port.

2. Connect the provided power supply to the unit’s DC connector. The unit

immediately receives power once you connect a power source to it.

3. When the unit completes the boot process, the left-most eight LEDs

indicate how the analog ports are configured. A red light indicates the port

is FXO, and a green light indicates the port is FXS. If the light for a port is

off, the port is not installed.

Note: The analog port configuration is selected when you purchase your CSG

unit.

4. Connect telephones to the analog ports that are configured as FXS ports

and connect phone lines to the analog ports that are configured as FXO

ports. If you are using the CSG-500, you can skip this step.

WARNING!

If you are using the CSG-544, do NOT connect analog ports 1-4 to

a phone line. Since both the FXS port and the phone line supply

power, the hardware could sustain damage. This damage is not

covered under the AMX standard warranty.

Instructions for Wall Mounting

1. Select the area to mount the CSG unit. The unit should be mounted at or

below eye level to properly view the LEDs.

2. Line up one of the surface mounting brackets with the two holes on one

side of the CSG. Install two #4-40 X .250 PPH screws into the holes in the

bracket to secure the bracket to the CSG.

3. Repeat step 2 to attach the second bracket to the other side of the unit.

4. Affix one screw to the wall.

Leave approximately 1/4-inch of the screw

protruding from the wall to allow the head of the screw to slide into the

settings on the mounting bracket, mounting the unit to the wall.

5. Repeat step 4 to attach the second bracket to the wall.

Understanding the LEDs

There are 14 LEDs on the front panel of the CSG. The eight LEDs corresponding

to the analog ports on the rear panel indicate the type of interface installed. The

following table explains the definition of each LED and its color representation:

CSG Specifications

Dimensions 1.74” x 11.45” x 5.44” (4.41 cm x 29.09 cm x 13.82 cm)

Weight 2.25 lbs. (1.02 kg)

Enclosure Metal with black matte finish

Power

Requirements

Constant current draw: 2.6 A @ 12 VDC

Memory • 8MB on board serial Flash memory

• 64MB 16-bit parallel SDRAM

Certifications FCC (Class A), CE, IEC60950, and RoHS

Operating/

Storage

Environment

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Operating Humidity: 5% to 85% RH Non-Condensing

• Storage Temperature: -20° C (-4° F) to 70° C (158° F)

• Storage Humidity: 0% to 85% RH Non-Condensing

Front Panel Components:

Power LED Indicates whether the unit is turned on and receiving power.

Network LED Indicates whether a network cable is connected and the speed of

the network.

IP Phones

LEDs

Indicates whether the corresponding link is connected and the

speed of the link.

Analog LEDs Indicates whether the analog port is installed and the type of port

(FXO/FXS) installed. (Not available on all models.)

Rear Panel Components:

Power

connector

5.1mm OD, 2.1mm pin, 12V 3.0A center positive

Configuration

Reset Switch

Resets the current configuration to the factory default when

pressed continuously during the boot process.

Console port 1 RJ45 port for console (craft) port serial control

Network port 1 RJ45 10/100baseT port for a general (WAN) connection

IP Phones

ports

4 RJ45 10/100baseT ports for IP phone connections

Analog ports • 8 RJ11 ports: 4 for FXO and 4 for FXS connections (CSG-544

only)

• 8 RJ11 ports for FXO connections (CSG-580 only)

Note: The CSG-500 does not use analog ports.

CSG Specifications (continued)

Included

Accessories

• PSN3.0, Power Supply, 3.0A, 12.0CVD (FG423-31)

• CSG SIP Communications Gateway Installation Guide

(93-2182-01)

• 2 Surface mounting brackets (62-2182-04)

• 4 #4-40 X .250 PPH screws (80-0112)

Other AMX

Equipment

• DIN Rail Mounting Bracket (FG532-06)

LED Definitions

LED Color Description

Power Blue (pulsing) On when the unit boots up after the bootload process

has completed. The LED pulses at a rate which is

proportional to the BlackFin processor load.

Network Off No line is connected or the interface is inactive.

Green

(flashing)

Link is up at 100Mbps. LED flashes at 1/10 second

intervals as traffic is detected.

Red (flashing) Link is up at 10Mbps. LED flashes at 1/10 second

intervals as traffic is detected.

Phones

(4 ports)

Off No line is connected or the interface is inactive.

Green

(flashing)

Link is up at 100Mbps. LED flashes at 1/10 second

intervals as traffic is detected.

Red (flashing) Link is up at 10Mbps. LED flashes at 1/10 second

intervals as traffic is detected.

1 2

Résumé du contenu

Page 1 - Installation Guide

Installation GuideCSG SIP Communications Gateway (CSG-500/544/580)ATTENTION: READ THIS FIRST!For more detailed installation, configuration, programmin

Page 2 - Setting Up Your System

Plus de documents pour Mise en réseau AMX CSG-580

Voir le document AMX CSG-580 Spécifications

AMX CSG-580 Spécifications (202 pages)

AMX CSG-580 Spécifications (64 pages)

Commentaires sur ces manuels

Pas de commentaire

AMX CSG-580 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Mise en réseau AMX CSG-580. AMX CSG-580 Installation guide Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Mise en réseau AMX CSG-580

Commentaires sur ces manuels

Produits connexes et manuels pour Mise en réseau AMX CSG-580