AMX DAS-TAMP8-SIG Manuel d'utilisateur télécharger pdf

Installation Guide

DAS-T0804/8-SIG Tango Audio Controllers

Overview

The Tango Series of Audio Controllers allow centralized control of common audio equipment

for up to 4 or 8 independently controlled audio zones per Controller. Each Tango Controller is

capable of controlling the source via Metreau Keypad, RS-232, IP address (via the optional

Ethernet Module), SWT Speakers (equipped with IR receivers), or the MIO R-1 AUDIO IR

remote control. Other sources such as Satellite Receivers, CD Players, MP3 Players, and

any other IR Controlled audio source can be patched into the RCA source inputs on the rear

panel (FIG. 1).

Tango Series Audio Controllers are available in two variations with two power options for

each:

• DAS-T0804-SIG - Tango 8-Source, 4-Zone Audio Controller. The DAS-T0804-SIG can

control 8 sources and distributes audio to 4 rooms/zones.

110VAC Power: FG1103-01

220VAC Power: FG1103-03

• DAS-T0808-SIG - Tango 8-Source, 8-Zone Audio Controller. The DAS-T0808-SIG can

control 8 sources and distributes audio to 8 rooms/zones.

110VAC Power: FG1103-02

220VAC Power: FG1103-04

Both Tango Controllers are expandable to 64 zones via Tango Zone Expanders.

Product Specifications

The following table provides technical specifications for the Tango Audio Controllers. Unless

otherwise noted, these specifications apply to both the DAS-T0804-SIG and DAS-T0808-

SIG models.

Rack-Mounting

Tango units occupy two rack spaces in a standard 19" equipment rack. Rack mounting

brackets are supplied with the optional Rack-Mount Installation Kit (FG1101-60).

Note: Exercise extreme care when lifting or moving Tango units within the rack to avoid

injury. It is recommended that you seek the assistance of another person when rack

mounting Tango units.

1. Attach the rack mounting brackets to each side of the Tango unit using the four screws

(10-32 Panhead Phillips - supplied with the Tango unit) for each bracket.

Note: To prevent injury the Tango unit must be securely attached to the rack in accor-

dance with the installation instructions. ALWAYS use the special rack mount brackets

supplied and high quality fixing screws to ensure the Tango unit is installed in the rack

correctly.

2. Place the Tango unit in the equipment rack and hold steady.

3. Secure the Tango unit in the rack using the mounting holes.

Note: DO NOT stand other units directly on top of the Tango unit when it is rack

mounted, as this will place excessive strain on the mounting brackets.

Ventilation

To ensure that the rack enclosure is adequately ventilated, there must be a minimum of 3" all

around the Tango unit.

Sufficient airflow must be achieved (by convection or forced-air cooling) to satisfy the

ventilation requirements of all the items of equipment installed within the rack.

FIG. 1 Tango Audio Controllers

Tango Audio Controllers - Product Specifications

Power: AC range of the US version is around 106 -128 V AC

960W max (Actual average usage = 300W)

Zone Support: DAS-T0804-SIG - 4 independent audio zones.

DAS-T0808-SIG - 8 independent audio zones.

• Each zone is protected thermally.

• Zone grouping.

• Independent Volume, Bass, Treble, Balance and SRS

controls in each zone.

Stereo Amplifiers: • 40 Watts/CH stereo amplifiers (20Hz to 20Khz @ .1% THD).

• Stereo Output:20Hz to 20Khz @ .1% THD

• Protected from overload and thermal runaway.

SRS/WOW

: SRS/WOW

audio enhancement technology on all zones.

Note: SRS/WOW is a registered trademark of SRS labs, Inc.

Front Panel Components:

Light Bar Blue light bar indicates power status.

LEDs Blue LEDs indicate zone status.

Function/Navigation

Buttons

5 pushbuttons allow for front panel programming, selection of

sources, tuning AM/FM radio stations (when equipped with the

optional AM/FM Tuner Card).

IR Receiver Receives IR signals from remotes (to audio source devices), so

the Controller can learn and emulate those commands.

LCD Display Displays information necessary during the programming steps

and afterward is the display to indicate information about the

source input activity.

Function Buttons

IR ReceiverLCD Display Screen

Power Switch &

Zone Outputs (4 or 8)

IR Outputs (8)

Expansion Port (RJ11) RS-232 (DB9)

Paging IN/OUT ports

Light Bar (power status)

LED Zone Status Indicator

Audio Inputs (4 or 8)

Audio Outputs (4 or 8)

Antenna Inputs

Receptacle

Tango Audio Controllers - Product Specifications (Cont.)

Rear Panel Components:

Power Switch

& Receptacle

The master power switch will remain in the ON position nor-

mally.

Paging In/Out Ports RCA jacks to connect to Paging devices (any audio signal/

source can be used as a paging device).

The Paging device connects to the Controller via the

"Paging In" connector.

The “Paging Out” connector is used to carry the page to Zone

Expander(s).

RS-232 Port DB9 connector allows the Tango Audio Controller to receive

Controller Command Messages and provide status messages.

AM/FM Antenna

Inputs

Connections for the AM and FM Antennas

(indoor installation only)

Audio Inputs Stereo Inputs, 47K impedance, buffered.

Audio Outputs Stereo Looping Outputs, buffered.

IR Outputs • Eight IR 3.5mm mono output jacks.

Zone Outputs • DAS-T0804-SIG: 4 zone output connectors (connect to

Metreau keypads)

• DAS-T0808-SIG: 8 zone output connectors (connect to

Metreau keypads)

Expansion Port RJ-11 Port connects main Controller with Tango Zone

Expanders.

Dimensions (HWD):

(including feet)

• 4" x 17" x 13 1/2" (10.2 cm x 43.2 cm x 34.3 cm)

•2 RU

Weight: Max. weight with 8 zones - 31 lbs (14.1 kg)

Included Accessories: • IR01 IR BLASTER MODULE (FG-IR01)

• FM antenna (indoor)

• Power Cord

Other AMX Equipment: • DAS-AMFM AM/FM Tuner Module (FG1110-01)

• DAS-MNET Network Interface Card (FG1101-61)

• DAS-MET-6SRC 6-Source Audio Keypad (FG1122-01-XX)

• DAS-MET-NUM Numeric Audio Keypad (FG1122-02-XX)

• DAS-T0804X-SIG Tango 4-Zone Expander:

110VAC Power: FG1103-11

220VAC Power: FG1103-13

• DAS-T0808X-SIG Tango 8-Zone Expander:

110VAC Power: FG1103-12

220VAC Power: FG1103-14

• DAS-TAMP4-SIG Tango 4-Channel Amplifier

110VAC Power: FG1103-21

220VAC Power: FG1103-23

• DAS-TAMP8-SIG Tango 8-Channel Amplifier

110VAC Power: FG1103-22

220VAC Power: FG1103-24

• DAS-MRMK Rack Mount Kit (FG1101-60)

1 2

Résumé du contenu

Page 1 - Tango Audio Controllers

Installation GuideDAS-T0804/8-SIG Tango Audio ControllersOverviewThe Tango Series of Audio Controllers allow centralized control of common audio equip

Page 2 - IR Sensor

Commentaires sur ces manuels

Pas de commentaire

AMX DAS-TAMP8-SIG Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Amplificateurs audio AMX DAS-TAMP8-SIG. Installation Guide - DAS-T0804/8-SIG Tango Audio Controllers - AV-iQ Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio AMX DAS-TAMP8-SIG